Tell us about the property and the problem. We’ll follow up to schedule a site visit.
Commercial Property Services
Parking Lot Striping
Restriping, layout and stall counts, ADA accessible spaces, fire lanes, and traffic markings.
Commercial lots across twelve Midwest states. Measured against the standards that actually apply, and confirmed with your local authority before anything is painted.
Before you repaint the same pattern
Striping is usually sold as a refresh. It is two other things as well.
Striping is the only practical moment the layout is in play. Once new lines go down they stay for years, so repainting the existing pattern by default forecloses the one chance to improve it.
It is also where ADA parking compliance is physically defined — stall widths, access aisles, hatching, the symbol on the pavement, and where the accessible spaces sit relative to the entrance.
Those two facts are why a striping bid deserves more attention than its price suggests. A lot being restriped is a lot whose accessible space count, van-accessible provision, aisle widths, and stall positioning can all be corrected for the cost of paint. The same lot restriped to its existing pattern carries every one of those deficiencies forward for another several years.
There is a hard limit worth stating up front. Paint defines dimensions; it cannot change slope. Accessible spaces and their aisles must be no steeper than 1:48 in any direction, and where the pavement exceeds that, no layout brings it into compliance. That is pavement work, and we measure it before quoting so you know which problem you have.
The other thing we do before painting is confirm requirements locally. Fire lane marking specifics are set by the authority having jurisdiction and genuinely differ between municipalities, and standard stall dimensions come from local zoning rather than any national standard. Across twelve states, assuming is how a lot gets painted twice.
Capabilities
Markings we lay out and apply
Stalls, accessibility, traffic control, and fire lanes — measured and laid out rather than traced over what was there.
Call 309-796-2222- Restriping to the existing layout
- New layout and stall count studies
- Angled and 90-degree configurations
- Drive aisle widths to local zoning
- Numbered and reserved stalls
- Compact and oversize designations
- Motorcycle and bicycle areas
- Line removal and blackout
- Accessible stall and aisle layout
- Van-accessible space provision
- Space count corrections
- Access aisle hatching
- Pavement accessibility symbols
- Signage and post installation
- Sign height correction
- Route marking to the entrance
- Directional arrows and lane markings
- Stop bars and yield markings
- Crosswalks and pedestrian paths
- Hatched and cross-hatched areas
- Loading and delivery zones
- Curbside pickup and EV stalls
- Speed bump marking
- Stenciled text and legends
- Fire lane striping to local requirements
- Stenciled fire lane legends
- Fire lane signage
- Red and yellow curb painting
- Island and median marking
- Bollard and wheel stop painting
- Hydrant and FDC zone marking
- Confirmation with your fire marshal
Reference
Four authorities, applying to different parts of the same site
This is the part most commonly misunderstood, including by contractors. Knowing which rule governs which area is what keeps a lot from being marked to the wrong standard.
Reference
Accessible parking that striping defines
Counts are calculated per parking facility rather than across a property, so a site with several separate lots is figured lot by lot.
| Total spaces in lot | Accessible spaces required | Of those, van accessible |
|---|---|---|
| 1 to 25 | 1 | 1 |
| 26 to 50 | 2 | 1 |
| 51 to 75 | 3 | 1 |
| 76 to 100 | 4 | 1 |
| 101 to 150 | 5 | 1 |
| 151 to 200 | 6 | 1 |
| 201 to 300 | 7 | 2 |
| 301 to 400 | 8 | 2 |
| 401 to 500 | 9 | 2 |
| 501 to 1,000 | 2% of the total | 1 of every 6 |
| 1,001 and over | 20, plus 1 per additional 100 | 1 of every 6 |
At least one van-accessible space is required in every case, however small the lot. The dimensional requirements below are what striping actually establishes:
Layout
Worth asking while the lot is open anyway
Most lots were laid out for how the property was used when it was built. Restriping is the one moment that can be revisited at the cost of paint rather than construction — and on some lots it recovers usable stalls from circulation that never worked well.
90-degree parking generally maximizes stall count. Angled parking with one-way aisles is easier to navigate and can improve flow. Which wins depends on the lot's shape and how it is used.
Checked against what your local zoning requires rather than carried forward. Aisles wider than necessary are stalls you are not getting.
The standards require them on the shortest accessible route to an accessible entrance. On older lots they frequently are not, and that is a layout fix.
Delivery and pickup patterns drift over the years. Marking the zones where they really occur beats enforcing zones that no longer match the operation.
Neither existed when most lots were laid out. Both need designated space, and both are easier to establish during a restripe than to retrofit later.
On plenty of lots the existing layout is already the right one. We will say so rather than selling a study. The question is free while we are measuring anyway.
Reference
Materials and where each belongs
Waterborne paint is right for most of a parking lot. The upgrade is worth its cost in specific places rather than across the whole field.
On timing: traffic paint requires a minimum surface temperature and dry conditions to cure, and surface temperature matters more than air temperature — pavement can sit well below the threshold on a mild morning. Paint applied too cold or onto a damp surface fails early, in ways that are not obvious for months. That makes striping a planned operation in this region rather than one ordered on demand.
Process
How we scope and lay out a striping job
Straight restripes, full re-layouts, and work driven by an accessibility report all start the same way.
Call 309-796-2222Measure the lot and the accessible elements
Stall and aisle dimensions, accessible space counts and widths, slopes, route widths, and sign heights recorded as actual measurements. Slope is checked specifically, because it is the one thing paint cannot fix.
Confirm requirements locally
Fire lane marking with your fire marshal, stall dimensions and aisle widths against local zoning. These differ between jurisdictions, and confirming beforehand is cheaper than repainting.
Agree the layout before paint
Restripe as-is, or a revised layout with the stall count and trade-offs stated plainly. Where the existing layout is already right, we say so.
Lay out, apply, and document
Measured and chalked before painting, applied in phases around your hours, with post-work dimensions recorded for the accessible spaces and routes.
About our striping work
What we bring to a striping job
Laid out from measurements against the standards, not painted over the pattern that was there. Tracing an existing layout carries its deficiencies forward for years.
Counts, widths, aisles, hatching, symbols, sign heights, and position relative to the entrance — all checked, with slope measured and reported separately as pavement work.
Fire lane specifics with your authority having jurisdiction, stall dimensions against local zoning. Across twelve states these genuinely differ.
Repair, crack sealing, and sealcoating in the correct order ahead of paint, so markings are not applied to a surface that is about to be worked on.
Early mornings, evenings, and weekends, sequenced so the stalls out of service at any moment are the ones you need least.
One account, one contact, and a consistent standard across every property, in twelve Midwest states. Operating this way since 1996.
Common questions
Parking lot striping questions
Answers referencing the ADA Standards are general information, not legal advice. Fire lane specifics are confirmed with your local authority.
Call 309-796-2222How often does a commercial lot need restriping?
It depends on traffic volume, snow removal, sun exposure, and what the lines were painted with, so there is no single interval worth quoting.
What drives it in this region is plow traffic more than tires. A blade crossing a stall line all winter removes paint faster than a season of parking does, so lots in the snow belt generally need attention sooner than the same lot would further south.
The practical trigger is legibility rather than the calendar. When drivers stop parking squarely because the lines have gone faint, when the accessible stall markings are no longer clearly defined, or when the hatching in an access aisle has worn away, it is time. We would rather look at the lot than quote from an interval.
Can restriping fix our ADA parking problems?
Partly, and this is the most important limit to understand before you spend anything.
Striping defines the accessible stalls — their width, the access aisle, the hatching, the symbol on the pavement, and where the spaces sit relative to the entrance. A great many ADA parking deficiencies are genuinely layout and marking issues, and those can be corrected with paint at modest cost: a lot missing a van-accessible space, an aisle that is too narrow, stalls too far from the entrance, or a count that is short for the size of the lot.
What paint cannot change is slope. Accessible spaces and their access aisles must be no steeper than 1:48 — roughly 2% — in any direction, and if the pavement exceeds that, no striping layout brings it into compliance. That is concrete or asphalt work.
The same applies to the route from the space to the entrance: 36 inches minimum clear width, firm and stable, with no curbs or stairs. A striped path across a lot does not satisfy it if it crosses a curb. We measure slope and route before quoting, so you know which category you are in. See ADA access, ramps and bollards.
How many accessible spaces does our lot need?
It scales with the total in that lot, and each parking facility is counted separately rather than across the whole property.
One space for 1–25 total, two for 26–50, three for 51–75, four for 76–100, five for 101–150, six for 151–200, seven for 201–300, eight for 301–400, nine for 401–500, then 2% of the total from 501 to 1,000, and 20 plus one per additional 100 above that.
At least one of every six accessible spaces — or fraction of six — must be van accessible, and there must always be at least one van-accessible space regardless of how small the lot is. Small lots with a single accessible stall and no van designation are among the most common deficiencies we find.
What are the dimensions for accessible stalls and aisles?
A car space is 96 inches wide minimum with a 60-inch minimum access aisle. A van space is either 132 inches wide with a 60-inch aisle, or 96 inches wide with a 96-inch aisle.
The access aisle must be at the same level as the space and run the same length, and it must adjoin an accessible route. Two car spaces may share one aisle, though not where the spaces are angled. A ramp may not extend into the access aisle.
Van spaces, their aisle, and the vehicle route to and from them need 98 inches of vertical clearance, which is what catches covered parking and structures.
Signage sits with the striping: the International Symbol of Accessibility with the bottom edge of the sign at least 60 inches above the ground, and a “van accessible” designation on van spaces.
Are there rules for the rest of the markings, or just the accessible spaces?
There are, and they come from different authorities that apply to different parts of the same site. This is worth understanding because it is widely misunderstood.
The ADA Standards are federal and govern the accessible elements — spaces, aisles, routes, and signage.
The MUTCD — the Manual on Uniform Traffic Control Devices — is the standard for traffic control on public roads, and it reaches some private property. Per FHWA's own guidance, it applies to roads within privately owned facilities such as shopping centers, parking lots, airports and arenas where those roads are open to public travel without access restrictions. But it expressly does not apply to parking areas or to the driving aisles within them, whether privately or publicly owned. So the through-drive across a shopping center can be subject to it while the parking field it serves is not.
The fire code governs fire lanes, and the specifics are local. IFC Section 503.3 requires fire apparatus access roads to be marked where the fire code official requires it, and the details — stripe color and width, lettering height and spacing, sign dimensions — are set by local amendment and by the authority having jurisdiction, who may also approve alternative markings.
Local zoning governs standard stall dimensions, counts, and aisle widths. There is no federal standard for those, which is why they differ from one municipality to the next.
What are the fire lane marking requirements?
They are set locally rather than nationally, so the real answer is that we confirm them with your fire marshal before striping.
IFC Section 503.3 establishes that fire apparatus access roads be marked where the fire code official requires it. The dimensional specifics come from local amendments and the authority having jurisdiction, and the code also allows the fire chief or a designee to approve alternative markings.
As a representative example of what an authority having jurisdiction specifies, one Midwest jurisdiction requires a 4-inch red stripe on each side of the access road along its entire length — with the curb painted red instead where a curb borders the lane — plus “NO PARKING—FIRE LANE” stenciled at least 12 inches high with a 2-inch stroke, repeated every 50 feet, and signs 12 by 18 inches with red letters on a white reflective background.
Treat that as an illustration, not a specification for your property. We operate across twelve states and these requirements genuinely differ between jurisdictions — sometimes between neighboring municipalities. Confirming before painting is cheaper than repainting.
Can we change the layout when we restripe?
Yes, and restriping is the only practical moment it is in play. Once new lines go down they tend to stay for years, so it is worth asking the question rather than repainting the existing pattern by default.
Things worth examining: stall angle, since 90-degree parking generally maximizes count while angled parking with one-way aisles can improve flow and is easier to navigate; aisle widths against what your local zoning requires; whether accessible spaces are positioned on the shortest route to the entrance as the standards require; where loading, pickup, and delivery actually happen versus where they were designed to; and dedicated space for EV charging or curbside pickup that did not exist when the lot was laid out.
On some lots a re-layout recovers usable stalls from circulation that was never efficient. On others it does not, and we will tell you that rather than selling a layout study. Either way the question costs nothing to ask while the lot is being striped anyway.
What kind of paint should be used?
Waterborne traffic paint is the standard for commercial parking lots and the right choice for most properties — it dries quickly, it has low VOC content, and it is economical enough to maintain on a reasonable cycle.
More durable materials exist and have their place. Thermoplastic is hot-applied and far longer-lived, which is why it dominates roadway work, but it is generally more than a parking field needs. Epoxy and methyl methacrylate systems last longer than waterborne paint at higher cost and with longer cure times. Preformed thermoplastic tape is useful for symbols, arrows, and crosswalks that take concentrated wear.
The practical approach on most lots is waterborne paint for stalls and a more durable material only where wear is concentrated — crosswalks, stop bars, arrows, and accessible symbols. We will tell you where that upgrade earns its cost and where it does not.
When can striping be done in the Midwest?
It is temperature and moisture dependent, which limits it to the warm season here more tightly than most people expect.
Manufacturers specify a minimum surface temperature and dry conditions for traffic paint to cure properly, and surface temperature matters more than air temperature — pavement can be well below the threshold on a mild morning. Paint applied too cold or onto a damp surface does not bond or cure correctly, and it fails early in ways that are not obvious for several months.
That makes striping a planned operation rather than one ordered on demand. Lots that go into budgeting over the winter get scheduled in favorable conditions; lots that call late in the season are competing for a narrowing window.
Does striping have to happen after other pavement work?
Yes, and getting the sequence wrong is one of the more common ways property owners pay twice.
The order is repair first, then crack sealing, then sealcoating, then striping. Sealer has to cure before paint goes on it, and the cure time is product-dependent rather than fixed. Paint applied over uncured sealer does not bond.
The expensive version of this mistake is striping a lot and then repairing or sealcoating it, which destroys the markings and means paying for them again. If any pavement work is planned this season, the striping belongs at the end of it. See parking lot repair.
How do you remove old lines when the layout changes?
Removal rather than painting over, where the layout is changing. Old lines showing through a new pattern create exactly the kind of ambiguity that causes drivers to park in the wrong place.
Grinding and water blasting are the usual methods, each leaving some scarring on the surface. Blacking out with pavement-colored paint is an option on lots that are also being sealcoated, since the sealer covers the old pattern completely and gives a clean surface for the new layout.
Which method fits depends on the pavement condition, how many lines are being removed, and whether sealcoating is part of the scope. On a lot getting a full re-layout, sealcoating first is usually the cleanest and most economical path.
Can the lot stay open during striping?
Yes, in sections. Striping is done area by area, with the painted sections closed only until the paint is dry enough for traffic — typically a short window with waterborne paint under good conditions.
For retail, medical, and other properties where stall availability matters, we work early mornings, evenings, or weekends and sequence the lot so the areas closed at any one time are the ones you need least. On most commercial lots the disruption amounts to a portion of the stalls being unavailable for part of a day.
We confirm the phasing against your operating hours before starting, and tell you which areas are down and when.
Related services
Commonly scoped alongside striping
Striping comes last. The pavement, concrete, and accessibility work comes first.
All ServicesRequest a bid on parking lot striping
Tell us the property, roughly how many stalls, and whether you want the existing layout or a revised one. We’ll follow up to schedule a measure.
309-796-2222- We walk the site and assess the actual condition.
- You get a priced scope before any work starts.
- Emergency? Call the number above instead of filling this out.
Send the details and we’ll be in touch to schedule a site visit.