Commercial Electrician & Electrical Repair | West Maintenance, Inc.

Commercial Property Services

Commercial Electrical

A breaker that keeps tripping is telling you something. We find out what.

Circuit troubleshooting, panels and service, lighting, exit and emergency lights, and LED retrofits — for commercial property across the Midwest since 1996.

Call 309-796-2222
Commercial drop ceiling and lighting installation
Something burning or sparking? 309-796-2222 Shut the circuit off if you safely can, then call. Don’t wait on a form.
Stop and call

Don’t reset it again if you see any of this

  • A breaker tripping daily, or immediately on reset
  • A burning, hot, or acrid smell near a panel or outlet
  • A panel, breaker, outlet, or switch that is warm to the touch
  • Scorch marks, discoloration, or melted plastic
  • Buzzing, crackling, or arcing sounds
  • Shocks or tingling from equipment or fixtures
  • Lights dimming when equipment starts
  • Water that has reached a panel or electrical equipment

A breaker is a safety device. Repeatedly resetting one removes the warning without removing the cause — and overheating connections are the usual path to an electrical fire. If any of the above is happening, shut the circuit off if you can do it safely and call us.

Call 309-796-2222

Where to start

What brought you here?

Electrical work arrives three ways. Whichever one you are in, it is the same phone number.

Something is wrong
Troubleshoot & Repair

A breaker that keeps tripping, a dead circuit, flickering, or a panel doing something it should not.

  • Circuit and breaker diagnosis
  • Dead outlets and partial power loss
  • Flickering and voltage problems
  • Panel and breaker replacement
Call 309-796-2222
An inspection is coming
Code & Compliance

Exit and emergency lighting, panel labeling and clearance, and the findings on a report you need closed out.

  • Exit and emergency light testing
  • Panel directories and labeling
  • Working clearance corrections
  • Open knockouts and missing covers
You’re planning work
Upgrades & Projects

LED retrofits, added capacity for equipment or a tenant, lot lighting, and build-out power.

  • LED retrofits with real payback math
  • Panel and service upgrades
  • Equipment and tenant circuits
  • Parking lot and exterior lighting
Breaker tripping or power out?
Call 309-796-2222. Electrical faults don’t get better on their own.
Call 309-796-2222

What it usually means

Common commercial electrical problems

Electrical faults are diagnostic problems. The symptom rarely points at the cause, which is why guessing gets expensive.

Call 309-796-2222
A breaker that keeps tripping

Too much load, a short or ground fault, or a weakened breaker tripping below its rating. Identical at the panel, three different repairs — and only one of them is replacing the breaker.

Lights dim when equipment starts

Usually a loose connection, an undersized circuit, or a service nearing capacity. It is also the symptom most often ignored until something fails.

Flickering or buzzing fixtures

A loose connection, a failing ballast or driver, or a dimming incompatibility. Buzzing at a switch or panel is worth looking at the same day.

Part of the building has no power

A tripped breaker is the easy case. A failed connection in a panel or a lost leg of service is the one that needs tracing before anything gets re-energized.

Outlets that work intermittently

Usually a loose connection, which means heat, which means it will eventually fail — often in the wall where you cannot see it happening.

Nobody knows what the breakers do

An unlabeled panel costs you time on every service call and is a routine inspection finding. Mapping and labeling it is a cheap half-day that pays back for years.

What we do

Commercial electrical services

Repair, code corrections, and planned upgrades on the same account.

Call 309-796-2222
Troubleshooting & Repair
  • Circuit tracing and fault location
  • Breaker testing and replacement
  • Dead and intermittent outlets
  • Switches, devices, and GFCI
  • Loose and overheated connections
  • Motor and equipment circuits
  • Wiring repair and replacement
  • Panel mapping and labeling
Panels, Service & Capacity
  • Panel and sub-panel installation
  • Service upgrades and capacity review
  • Dedicated equipment circuits
  • Disconnects and safety switches
  • Transformer and feeder work
  • Tenant metering and separation
  • EV charging circuits
  • Generator and transfer coordination
Lighting
  • Interior lighting repair and replacement
  • LED retrofits and upgrades
  • High-bay and warehouse lighting
  • Parking lot and pole lighting
  • Wall packs and building-mounted
  • Illuminated sign repair
  • Timers, photocells, and sensors
  • Lighting controls and scheduling
Life Safety & Code
  • Exit sign repair and replacement
  • Emergency lighting testing and repair
  • Monthly and annual test documentation
  • Panel directories and labeling
  • Working clearance corrections
  • Covers, knockouts, and enclosures
  • GFCI and code-correction work
  • Inspection finding closeout

Life safety

Exit and emergency lights have a testing schedule

It is the electrical obligation most commonly missed, because nothing looks wrong until the power goes out — which is the one moment the equipment has to work.

What NFPA 101 requires

Battery-powered emergency lighting and exit signs need a functional test of at least 30 seconds every 30 days, plus an annual test where the unit stays lit for a full 90 minutes.

Self-testing units can satisfy the monthly check with a look at the indicator, but the annual 90-minute test still applies. The building owner keeps written records — unit, date, test type, result — available to the authority having jurisdiction. Inspectors typically ask for the last twelve months.

Here is the honest part: the code does not require a licensed contractor for these tests. Your staff can do them, and some buildings do.

What most property managers would rather hand off is the annual 90-minute test, the recordkeeping, and having the failures fixed in the same visit instead of generating a list of units to chase. A unit that fails stays a deficiency until it is repaired or replaced.

The other three findings we see constantly are cheap to fix and routinely cited: panels with no legible directory, storage blocking the working clearance in front of a panel, and open knockouts or missing covers. If an inspection is coming, those are the easiest wins available.

Adopted code editions vary by jurisdiction — confirm specifics with your AHJ. We will tell you what we find on your building and what it takes to close it out.

Planned work

LED retrofits, with the math done on your building

We are not going to quote you a savings percentage off a brochure. Payback depends on five things, and four of them are specific to your property.

Call 309-796-2222
Run hours

The biggest single driver. A warehouse lit sixteen hours a day pays back in a fraction of the time an office lit eight hours does.

Your actual rate

What you pay per kilowatt-hour, from your bill — not a regional average. It moves the answer more than most people expect.

What you’re replacing

Metal halide and older fluorescent make a far stronger case than recent fixtures. Not everything on a property is worth retrofitting.

Maintenance you stop paying

Often overlooked and sometimes decisive. Relamping pole lights and high bays costs labor and a lift every time.

Utility rebates

Many utilities offer them for commercial lighting. We check what is available on your account before pricing the job.

What we’ll tell you

Which fixtures are worth doing and which are not. If the payback does not work in your building, you will hear that instead of a proposal.

Why West Maintenance

Why property managers call us for electrical

Call 309-796-2222
We diagnose before we price

You approve a known repair rather than an open meter. Troubleshooting is the honest variable, and we treat it that way.

Permits and inspections handled

We pull what the work requires and coordinate the inspection — and we will tell you when a job genuinely does not need one.

Planned shutdowns, not surprises

When something has to come down, you know in advance exactly what loses power and for how long.

The ceiling and the wall too

New circuits and fixtures mean drywall, ceiling tile, and paint. We put the building back instead of leaving holes.

Documentation that survives an audit

Test records, panel directories, and closeout notes in a form you can hand to an inspector or up the chain.

One building or a hundred

Single sites and multi-location portfolios on one account, one contact, and one consistent standard since 1996.

How we work

Three steps from fault to fixed

No contract required. Plenty of accounts start with one tripping breaker.

Call 309-796-2222
Step 01
Call with the symptom

What is happening, what is affected, and whether anything is hot, smells, or sparks. That last answer decides how fast we move.

Step 02
We diagnose, then price

We find the actual fault before quoting the repair, so you are approving a defined scope rather than open-ended hours.

Step 03
We repair and document

The repair, the finishes we had to open, and a written note of what was found — for your records and the next inspection.

What helps when you call: which panel or area is affected, what the breaker is doing, what changed recently, and whether any equipment was added. None of it is required — call with nothing but the symptom and we will still come look.

Common questions

Commercial electrical FAQs

Not covered here? Call and ask — we would rather answer it on the phone than have you guess.

Call 309-796-2222
My breaker keeps tripping. Is that dangerous?

A breaker that trips repeatedly is doing its job — it is telling you a circuit is drawing more than it should, or that there is a fault. Resetting it over and over removes the warning without removing the cause, and that is how electrical fires start.

There are three common reasons: too much load on the circuit, a short or ground fault in the wiring or a device, or a breaker that has weakened and now trips below its rating. They look identical at the panel and need different repairs.

If it is tripping daily, or if the panel or a device is warm, discolored, or smells hot, stop resetting it and call 309-796-2222.

What should I do if I smell something burning near a panel or outlet?

Treat it as urgent. If it is safe to reach the panel, shut off the affected circuit. Do not keep using the equipment on it, and call 309-796-2222.

A hot or acrid smell near electrical equipment usually means a connection is arcing or overheating. That is a condition that gets worse, not better, and it is the single most common thing we are called out for after hours.

How often do exit signs and emergency lights have to be tested?

Under NFPA 101, battery-powered emergency lighting and exit signs require a functional test of at least 30 seconds every 30 days, plus an annual test where the unit must stay lit for a full 90 minutes. Self-testing units can satisfy the monthly check with a visual look at the indicator, but the annual 90-minute test still applies.

The building owner is responsible for the testing and for keeping written records — unit, date, test type, and result — available to the AHJ. Inspectors usually ask for the last twelve months.

Worth knowing honestly: the code does not require a licensed contractor for these tests. Your staff can do them. Most buildings we work in would rather hand off the annual 90-minute test and the recordkeeping, and have failures repaired in the same visit. Adopted editions vary by jurisdiction, so confirm with your AHJ.

Do I need a permit for commercial electrical work?

Usually yes for anything beyond like-for-like replacement — new circuits, panel or service changes, added equipment, and most build-out work. Repairs and direct replacements often do not.

We pull permits and coordinate inspections as part of the job rather than leaving it to you. If a project genuinely does not need one, we will tell you that too.

Can you work without shutting the building down?

Most of the time, yes. We schedule shutdowns around your operations — nights, early mornings, weekends — and when a circuit or panel genuinely has to come down, you know in advance exactly what loses power and for how long.

The planning matters more than the work on an occupied property. A surprise outage in a clinic or a warehouse costs more than the repair did.

How much does commercial electrical work cost?

Troubleshooting is the honest variable. Finding an intermittent fault in a building with thirty years of undocumented additions takes longer than finding a dead circuit, and no one can quote that accurately over the phone.

What we can do is diagnose first and price the repair second, so you are approving a known scope instead of an open meter. For planned work — lighting, panels, equipment circuits — you get a firm itemized number before anything starts.

Is an LED retrofit actually worth it?

Often, but the payback depends on things specific to your building, not on a brochure number. The drivers are how many hours the lights actually run, what you pay per kilowatt-hour, what you are replacing, your maintenance cost on the existing fixtures, and whether your utility offers a rebate.

A warehouse running lights sixteen hours a day pays back far faster than an office running eight. Parking lot and high-bay fixtures usually make the strongest case, because the lamp replacement labor on them is expensive on its own.

We will do the math with your actual run hours and rate rather than quoting a generic savings percentage. If it does not pay back in your building, we will say so.

Why are half my parking lot lights out?

Several out at once usually points at a circuit, photocell, or contactor fault rather than individual lamps. One out is a lamp or driver; a row out is upstream of all of them.

It is worth fixing quickly — a dark lot raises your exposure on slips, vehicle break-ins, and after-hours incidents, and it is the first thing an insurer asks about afterward. See parking lot lighting.

Can you upgrade my panel or service for new equipment?

Yes — panels, sub-panels, service upgrades, and dedicated circuits for new equipment or a tenant's requirements. This comes up most with build-outs, kitchen equipment, shop machinery, and EV charging.

The first question is always whether the existing service has capacity. That is a calculation, not a guess, and it decides whether you are adding a sub-panel or upgrading the service.

What are the most common code issues you find?

Three, over and over. Panels with no legible directory, so nobody knows what a breaker controls. Blocked working clearance in front of panels — storage stacked where a technician has to stand. And open knockouts or missing covers on panels and junction boxes.

None are expensive to correct, and all three are routinely cited. If you have an inspection coming, those are the cheapest findings to get ahead of.

Do you handle signs, and lighting controls?

Yes — illuminated sign repair and maintenance, plus timers, photocells, occupancy sensors, and lighting controls. A dark sign costs you walk-in traffic every evening and is usually an inexpensive fix once someone actually looks at it.

Request a bid on commercial electrical

Tell us what the system is doing and which building. We’ll follow up to schedule a site visit.

309-796-2222
Call or send the form — we answer both.
  • We walk the site and assess the actual condition.
  • You get a priced scope before any work starts.
  • Emergency? Call the number above instead of filling this out.
Request a Bid

Send the details and we’ll be in touch to schedule a site visit.


Call Now