Commercial Concrete Repair & Sidewalk Replacement | West Maintenance, Inc.

Commercial Property Services

Concrete Repair

Sidewalks, curbs, entries, dock aprons, and equipment pads — repaired, replaced, lifted, or resurfaced.

Commercial flatwork and site concrete across twelve Midwest states. Scoped and priced by panel, placed to a specification we will show you.

Call 309-796-2222
Commercial concrete sidewalk replacement on a property we maintain
Speak with us directly 309-796-2222 Monday through Friday, 8:00 AM to 4:30 PM. Ask for concrete.

How concrete fails

Two unrelated failure mechanisms

Summary

Commercial concrete fails in two entirely separate ways, and nearly every wrong repair comes from treating one as the other.

Surface deterioration — scaling, spalling, delamination — originates in the concrete itself: air entrainment, finishing, strength, curing, and the deicers applied to it. Structural and subgrade movement — settlement, offset panels, working cracks — originates underneath the slab, in support rather than material.

The distinction decides everything. A settled panel with a sound surface is a candidate for lifting, which is fast and inexpensive. A scaled panel sitting on good subgrade is a candidate for an overlay. Treat the first as a material problem and you resurface a slab that is going to keep sinking. Treat the second as a support problem and you lift a slab whose surface is already gone.

Both mechanisms are worse in this climate than almost anywhere else. Freeze-thaw cycling is the primary driver of surface deterioration, and deicing chemicals intensify it by keeping surfaces saturated and increasing the number of cycles. Frost action in the subgrade drives the movement side — heave when it freezes, loss of support when it thaws.

The useful consequence is that a great deal of concrete condition on a commercial property was determined on the day it was placed. Air content, finishing practice, and whether water was added on site set how a slab will handle twenty Midwest winters. That is why we publish the specification we place to, further down this page.

Reference

What each type of concrete distress indicates

The first question on any concrete condition is which of the two mechanisms produced it. These are the patterns we record most often and what each one points to.

Scaling

Shallow flaking or peeling of surface mortar across an area. Freeze-thaw damage to a surface with insufficient entrained air, low strength, or a weak finish — intensified by deicers. A surface repair or overlay, not a replacement, where the slab below is sound.

Spalling over reinforcement

Deeper fragments breaking away, often in patches with rust staining or exposed steel. Chlorides have reached the reinforcement, which corrodes and expands, pushing the concrete off from beneath. Must be taken back to sound concrete with the steel addressed.

Delamination

The surface sounds hollow when struck but has not broken away yet. A plane of separation below an intact-looking surface, usually a finishing defect. It will become spalling — finding it early with a sounding survey lets it be repaired as a partial-depth patch.

Settled or offset panels

A panel sitting lower than its neighbor. A support problem rather than a concrete problem. Candidate for slab lifting if the panel is sound — but the void has a cause, and a failed storm line or eroding utility trench needs finding before the lift.

Working cracks

Cracks that are widening, offsetting vertically, or moving under load. Structural or subgrade in origin, unlike shrinkage cracking. Sealing them treats the symptom; the movement has to be addressed.

Shrinkage cracking and crazing

Early, narrow, stable cracks, or a fine cosmetic network of hairlines. Normal behavior rather than a defect. Worth sealing to keep water and chlorides out of the slab, but not a structural concern.

Random cracking across panels

Cracks ignoring the joint pattern. Usually too few control joints, or joints cut too late or too shallow to control where shrinkage went. The slab cracked where it chose because nothing told it where to.

Deteriorated joints

Spalled or broken joint edges with failed or missing sealant. Joints are where most flatwork deterioration begins, because they are the easiest route for water and chlorides into the slab and down to the subgrade.

Ponding on flatwork

Water standing on a walk, entry, or apron rather than draining. It keeps the surface saturated, which is the precondition for freeze-thaw damage, and concentrates salt solutions in one place. A grade problem that shortens the life of everything around it.

Concrete repair across twelve Midwest states
Call 309-796-2222 or request a written bid. Scoped and priced by panel.
Call 309-796-2222

Reference

Repair methods and when each applies

Concrete is more repairable than most property managers assume. Full replacement is one option among many, and frequently not the right one.

Panel replacement The failed panel is removed at its joints and replaced without disturbing adjacent panels. The default for deteriorated or broken flatwork, and the reason concrete can be repaired selectively. Broken or deteriorated panels
Partial-depth repair Deteriorated surface concrete is removed to sound material and replaced with a bonded repair mortar. Appropriate where damage is confined to the upper portion of the slab. Surface damage, sound slab
Full-depth repair Removal through the full slab thickness with subgrade correction and, where present, reinforcement repair or replacement before replacing the section. Through-slab failure
Slab lifting Polyurethane foam injection or cement-based slurry fills the void beneath a settled slab and returns it to grade. Fast, and with foam the area typically reopens the same day. Settled but sound slabs
Grinding and saw-cutting A vertical offset is ground or cut to a compliant transition. Inexpensive, immediate, and limited to modest displacement where both panels are sound. Small trip hazards
Crack routing and sealing Stable cracks are routed and sealed to keep water and chlorides out of the slab and away from reinforcement. Maintenance rather than repair. Stable, non-working cracks
Joint repair and sealing Spalled joint edges rebuilt and joints resealed. Joints are where most flatwork deterioration begins, and where water enters most readily. Deteriorated or open joints
Epoxy injection Structural cracks pressure-injected to restore monolithic behavior. A structural repair, not a water-stopping measure, and specified accordingly. Structural cracking
Overlays and resurfacing A bonded overlay restores a scaled or worn surface where the slab beneath remains structurally sound, avoiding full replacement. Widespread surface loss
Penetrating sealer A breathable silane or siloxane sealer reduces water absorption while allowing the slab to dry. Applied once the concrete is reasonably dry, and resealed on a cycle. Protection and maintenance

Flatwork is already divided into panels by its joints, which makes selective replacement straightforward — a failed panel comes out at the joints and a new one goes in without disturbing its neighbors. There is no structural reason to replace sound panels, and we price by panel so you can stage the work.

Decision framework

Lift the slab or replace the panel

The practical question on nearly every settled sidewalk and entry. Lifting is faster and cheaper when it applies, and a wasted expense when it does not.

Lifting is the better value when
  • The panel is structurally intact and not broken into pieces
  • The surface is in sound condition
  • The problem is loss of support, not the concrete
  • The cause of the void is identified and resolvable
  • The area needs to return to service quickly
  • Matching adjacent panels matters visually
Replacement is the right answer when
  • The panel is badly cracked or in multiple pieces
  • The surface has scaled, spalled, or delaminated anyway
  • Reinforcement is corroding within the slab
  • The void is from a failed utility or storm line needing access
  • Subgrade has to be rebuilt or stabilized
  • Most panels along the run are failing together
Find the cause before the lift. A void under a slab has a reason — an eroding utility trench, a failed storm line, poorly compacted backfill, or water tracking along a foundation. Lifting a slab over an unresolved cause buys a level walk and the same settlement again. We look for the reason before quoting the repair.

Deicers

The deicer in your salt shed is a concrete decision

Chloride deicers mostly damage concrete indirectly — by keeping surfaces saturated and multiplying freeze-thaw cycles. But chemistry matters, and the National Ready Mixed Concrete Association names specific products that should never touch concrete. Some of them are sold as the gentler option.

Call 309-796-2222
Acceptable

NRMCA identifies calcium chloride and sodium chloride — rock salt — as acceptable on sound concrete, used in moderate amounts.

Never use

Ammonium sulfate, ammonium nitrate, and magnesium-based salts are described as chemically aggressive to concrete and should never be used. Worth checking what you actually buy.

Not in the first winter

New concrete should get no deicing chemicals through its first winter. It is still saturated and below full strength — the worst possible moment for them.

Sand for traction

Clean sand is the recommended alternative on new work. Inexpensive, effective, and far cheaper than resurfacing a slab that scaled in its first season.

Rinse the buildup

Where salt does get used, hosing off accumulation when conditions allow reduces how long surfaces stay saturated with salt solution.

Fix the drainage

Poor drainage that lets salt solutions pool raises scaling risk directly. The areas that scale first are usually the low spots and the ground under downspouts.

We put this in writing. New flatwork is handed over with deicer instructions, and we will brief whoever handles your snow and ice so the guidance reaches the person with the spreader rather than a file. See snow and ice removal.

What we place to

The specification for exterior concrete in this climate

We publish this because it gives you something to ask every bidder. A lower number on a bid sometimes reflects a lower specification rather than better pricing, and air content is where that shows up first.

Total air content 6 percent for concrete with 3/4-inch or 1-inch coarse aggregate. Entrained air is the primary defense against freeze-thaw damage. NRMCA CIP 2
Compressive strength 4000 psi for exterior slabs that stay continuously moist and receive deicers. 3500 psi minimum where those conditions do not apply. NRMCA CIP 2
Slump at placement 3 to 5 inches, with no water added on site. Added water promotes bleeding and segregation and weakens the surface. NRMCA CIP 2
Finishing Bleed water gone before finishing, no steel troweling on exterior slabs, no overworking. A broom finish is adequate for most exterior surfaces. NRMCA CIP 2
Curing Pigmented liquid membrane curing compound, or wet burlap under plastic sheeting, with temperature and moisture maintained. NRMCA CIP 2
Cementitious substitution Limited to 25 percent fly ash, 50 percent slag cement, or 10 percent silica fume by weight of cementitious material. NRMCA CIP 2
Sealing Breathable silane or siloxane sealer for slabs, applied once the concrete is reasonably dry. Late summer after several dry days is ideal. NRMCA CIP 2
Site paving reference ACI PRC-330-21, Commercial Concrete Parking Lots and Site Paving Design and Construction—Guide, for thickness design, jointing, and subgrade. ACI 330-21

Figures above follow NRMCA CIP 2, Scaling Concrete Surfaces. For site paving, ACI PRC-330-21 is the industry guide — note that it is a guide rather than a specification, with ACI 330.1 serving that role, so a bid citing 330 as a specification is citing the wrong document.

Accessibility dimensions. Walks, ramps, landings, and the route from accessible parking carry dimensional requirements — running slope, cross slope no steeper than 1:48, 36-inch minimum clear width, and level changes over 1/2 inch requiring a ramp. New flatwork is an opportunity to correct those, and a chance to create new findings if nobody measures. We measure before and after. See ADA access, ramps and bollards.

Our work

Walks, curbs, and steps

Commercial flatwork, curb, and stair work on property we maintain.

Call 309-796-2222
New commercial concrete sidewalk and curb
Sidewalk and curb work
New commercial concrete steps with handrail installed
Concrete steps and handrail

Process

How we scope and price concrete work

Single panels, trip hazard programs, and full replacement all start the same way.

Call 309-796-2222
01

Walk the site and sound the slabs

Distress identified by type and located by panel, with surface deterioration separated from movement. Suspect areas sounded for delamination, and offsets measured against the ADA thresholds rather than estimated.

02

Find the cause before the method

Voids, settlement, and ponding have causes. We look for the failed line, the eroding trench, or the grade problem first, because a repair over an unresolved cause has a known expiry date.

03

Itemized bid, priced by panel

Lift, patch, grind, or replace priced per location so work can be phased across budget cycles. Where the cheaper method is adequate, we say so; where it will fail, we explain why.

04

Placed to spec, then documented

Air content, strength, slump, finishing, and curing to the specification above. Handover includes post-work dimensions and written deicer and sealing guidance for the new work.

About our concrete work

What we bring to concrete work

Call 309-796-2222
A published specification

Air content, strength, slump, finishing, and curing stated openly. Most of a slab's thirty-year performance is decided on placement day, so that is where the scrutiny belongs.

Repair before replacement

Lifting, grinding, partial-depth patching, and overlays are all on the table. Replacement is one option among several and often not the economical one.

We look for the cause

Settlement and voids have reasons. Finding the failed line or the grade problem is what separates a repair that holds from one that recurs on a cycle.

Measured against the standards

Trip hazards and accessible routes measured to the ADA thresholds, before and after. New flatwork is a chance to fix findings, or to create them.

Protection guidance in writing

Deicer and sealing instructions handed over with the work, and relayed to whoever salts the property. The cheapest way to protect what you just paid for.

Single sites to portfolios

One account, one contact, and a consistent standard across every property, in twelve Midwest states. Operating this way since 1996.

Common questions

Concrete repair questions

If your question is not covered, call and ask. We would rather answer it directly than have you work from an assumption.

Call 309-796-2222
What is the difference between scaling and spalling?

They look similar and they are not the same problem, which matters because the repairs differ.

Scaling is the flaking or peeling of the surface mortar, generally shallow and spread across an area. The National Ready Mixed Concrete Association describes it as the result of repeated freezing and thawing: as saturated concrete approaches freezing, water expands into ice and stresses the surface. Deicing chemicals make it worse by keeping the surface saturated and increasing the number of freeze-thaw cycles.

Spalling is deeper — fragments breaking away from the body of the slab, often in distinct patches and frequently over reinforcing steel. Where rebar is involved, the mechanism is usually chloride-driven corrosion: salt reaches the steel, the steel corrodes, corrosion products occupy more volume than the original metal, and the expansion pushes the concrete off from beneath.

Scaling is typically a surface repair or an overlay. Spalling over corroding steel has to be taken back to sound concrete with the steel treated or replaced, because patching over active corrosion just relocates the failure.

Why did our concrete start scaling when the sidewalk next to it is fine?

Almost always air entrainment, finishing, or added water — meaning the difference was established the day it was placed, not by what has happened since.

Entrained air is the defense against freeze-thaw. It creates millions of microscopic bubbles that give expanding ice somewhere to go. NRMCA's recommended total air content is 6 percent for concrete with 3/4-inch or 1-inch coarse aggregate. Concrete placed without it, or with too little at the surface, has no mechanism to absorb that expansion.

Finishing destroys it just as effectively. Overworking the surface drives entrained air out of the top layer, finishing while bleed water is still present produces a weak surface mortar, and steel troweling an exterior slab seals and weakens the very surface that has to survive winter. NRMCA notes a broom finish is adequate for most exterior work.

Then there is water added on site to make placement easier. It raises the water content, promotes bleeding and segregation, and weakens the surface. Two slabs placed the same week by different crews can have genuinely different life expectancies for this reason alone.

Does deicing salt damage concrete?

The relationship is more specific than yes or no, and the chemistry you buy matters more than the quantity.

Chloride deicers do not attack sound, properly air-entrained concrete directly so much as they worsen the freeze-thaw cycle — they keep the surface saturated and increase the number of cycles it goes through. On concrete that is already low in entrained air, low in strength, or poorly finished, that is enough to cause scaling.

Chemistry is the part most property managers have never been told. NRMCA identifies calcium chloride and sodium chloride (rock salt) as acceptable, and states that ammonium sulfate, ammonium nitrate, and magnesium-based salts are chemically aggressive to concrete and should never be used. That is worth checking against whatever is actually in your salt shed, because some of those are marketed as gentler alternatives.

The other factor is drainage. Poor drainage that lets salt solutions pool raises scaling risk, which is why the places that scale first are usually the low spots and the areas under downspouts.

Can deicers be used on concrete we just had poured?

Not during the first winter, and this is the single most valuable thing we can tell a client about protecting new work.

NRMCA's guidance is to avoid deicing chemicals on new concrete through its first winter, then use them in moderate amounts afterward. New concrete is still relatively saturated and has not reached its full strength, and that is exactly the condition in which deicers do the most damage.

Use clean sand for traction instead. It is inexpensive, it works, and it costs nothing compared with resurfacing a slab that scaled in its first season. Where salt does get used, hosing off accumulation when conditions allow helps.

We put this in writing when we hand over new flatwork, and we will brief whoever handles your snow and ice so the instruction actually reaches the person with the spreader. See snow and ice removal.

Should new concrete be sealed?

Yes, for exterior flatwork in this climate — with the right product and at the right time.

NRMCA recommends a breathable silane or siloxane sealer intended for slabs, applied once the concrete is reasonably dry and following the manufacturer's directions. Late summer, after a few dry days, is described as ideal.

The word doing the work there is breathable. A film-forming sealer that traps moisture in the slab can make freeze-thaw damage worse rather than better, which is the opposite of the intent. Penetrating silane and siloxane products reduce water absorption while still letting the slab dry.

Resealing on a cycle is reasonable maintenance and considerably cheaper than surface repair.

A sidewalk panel has settled. Can it be lifted instead of replaced?

Often, and it is usually both faster and less expensive when the slab itself is sound.

Slab lifting — polyurethane foam injection, or cement-based slurry in the traditional mudjacking approach — raises a settled slab back to grade by filling the void beneath it. It is appropriate when the panel is structurally intact and the problem is support rather than the concrete, and the area can generally return to service the same day with foam.

Replacement is the answer when the panel is badly cracked or broken into multiple pieces, when the surface has deteriorated anyway, or when the void is a symptom of something that has to be opened up and corrected — a failed storm line, an eroding utility trench, or subgrade that needs to be rebuilt.

Lifting a slab over an unresolved cause buys you a level walk and the same settlement again. We look for the reason before quoting the lift.

Is grinding a trip hazard an acceptable repair?

Sometimes, and it has clear limits.

Grinding or saw-cutting a vertical offset to a compliant transition is a legitimate and inexpensive fix for modest displacement where both panels are otherwise sound. It is quick, there is no cure time, and the walk is usable immediately.

It stops being appropriate when the offset is large enough that grinding would remove too much section or expose aggregate and reinforcement, when the panels have deteriorated, or when the cause is ongoing settlement that will reproduce the offset.

Under the ADA standards, a vertical change up to 1/4 inch is permitted as-is, between 1/4 and 1/2 inch must be beveled no steeper than 1:2, and anything over 1/2 inch has to be ramped. Those thresholds are what determine whether grinding resolves the condition or merely improves it. See ADA access, ramps and bollards.

What specification should commercial exterior concrete be placed to?

For this climate, the figures that matter most are air content, strength, and slump — and they are worth asking every bidder about, because a lower number on a bid sometimes reflects a lower specification rather than better pricing.

NRMCA's guidance for exterior slabs: total air content of 6 percent for concrete with 3/4-inch or 1-inch coarse aggregate. Compressive strength of 4000 psi for exterior slabs that will be continuously moist and receive deicers, with 3500 psi as the minimum where those conditions do not apply. Slump of 3 to 5 inches, with no water added on site.

Supplementary cementitious materials are limited to 25 percent fly ash, 50 percent slag cement, or 10 percent silica fume by weight of cementitious material.

For site paving specifically, ACI PRC-330-21, Commercial Concrete Parking Lots and Site Paving Design and Construction—Guide, is the industry reference. It is a guide rather than a specification — ACI 330.1 serves that purpose — and it covers thickness design, jointing, subgrade, accessibility surface requirements, and maintenance and repair.

When can concrete be placed in the Midwest?

Most of the year, with real caution at both ends of it.

NRMCA advises care when placing exterior concrete in late fall, winter, or early spring, because concrete that freezes soon after placement while still saturated is at high risk. Cold-weather placement is possible with blankets, heat, and mix adjustments, but it adds cost and it narrows the margin for error.

The practical consequence is scheduling. Exterior flatwork planned over the winter gets placed in favorable conditions in spring and early summer, which also puts it in position to be sealed in late summer as recommended, and to reach its first winter at full strength.

Where a repair genuinely cannot wait — a trip hazard, a failed entry, a broken dock apron — we will do it in the conditions available and tell you plainly what that means for its expected life.

Why does concrete crack, and which cracks matter?

Concrete shrinks as it cures and moves with temperature, so some cracking is expected rather than a defect. The useful question is which kind you have.

Fine surface crazing is a cosmetic network of hairlines and generally not a structural concern. Shrinkage cracking appears early and is usually narrow and stable. Control joints exist to put shrinkage cracking where you chose rather than where the slab decides, which is why slabs with too few joints, or joints cut too late or too shallow, crack randomly.

The cracks that matter are the ones that are widening, offsetting vertically, or working — moving under load. Those indicate subgrade or structural issues rather than shrinkage, and sealing them treats the symptom.

Sealing stable cracks is still worth doing. It keeps water and chlorides out of the slab and away from any reinforcement, which is the same logic that makes crack sealing the highest-value operation on asphalt.

Can you repair just the bad panels rather than the whole walk?

Yes, and panel-by-panel replacement is how most commercial flatwork should be handled.

Concrete flatwork is already divided into panels by its joints, which makes selective replacement straightforward — a failed panel comes out at the joints and a new one goes in without disturbing its neighbors. There is no structural reason to replace sound panels.

We scope and price by panel, which lets you address the trip hazards and failed sections now and stage the rest across budget cycles. It also gives you a documented record of which panels were replaced and when, which is useful if a claim ever arrives.

The honest exception: where most panels along a run are failing, replacing the run is usually cheaper per square foot than replacing them individually over several years, and we will say so.

Do you handle the curb, the pavement, and the ADA work together?

Yes, and on most sites those are the same job.

The curb line decides whether water leaves the lot or sits in it, so curb and gutter repair is frequently what makes an adjacent pavement repair last. Entry slabs, approach aprons, dock aprons, equipment pads, and bollard footings are all concrete work sitting against asphalt.

Accessibility is the other overlap. Walks, ramps, landings, and the route from accessible parking are concrete elements with dimensional requirements — cross slope, running slope, clear width, and level changes — and we measure those rather than assume them. See parking lot repair and ADA access work.

Request a bid on concrete repair

Tell us the property and what you are seeing — trip hazards, scaling, a settled panel, or a broken curb. We’ll follow up to schedule a walk.

309-796-2222
Call or send the form — we answer both.
  • We walk the site and assess the actual condition.
  • You get a priced scope before any work starts.
  • Emergency? Call the number above instead of filling this out.
Request a Bid

Send the details and we’ll be in touch to schedule a site visit.


Call Now