Commercial Pressure Washing & Soft Washing | West Maintenance, Inc.

Commercial Property Services

Commercial Pressure Washing

Building exteriors, walkways, drive-through lanes, dumpster pads, and graffiti — cleaned at the pressure the surface can take.

Pressure washing and soft washing for commercial property across twelve Midwest states, with the wash water contained and disposed of through a route that is actually permitted.

Call 309-796-2222
Commercial brick and stone veneer repair on a building exterior
Speak with us directly 309-796-2222 Monday through Friday, 8:00 AM to 4:30 PM. Ask for exterior cleaning.

Two things worth knowing first

The pressure and the water are both decisions

Summary

Pressure washing and soft washing are different services. Pressure cleans by mechanical force at 1,500 to 4,000 PSI or more. Soft washing cleans by chemistry at under 500 PSI. Most commercial cladding — shingles, vinyl, stucco, EIFS, wood, paint — needs the second one, and a contractor who only owns a pressure washer will use a pressure washer on all of it.

The wash water is regulated. It is industrial wastewater, it may not enter a storm drain, and on a commercial site nearly every parking lot drain is a storm drain.

Those two facts cover most of what separates a competent exterior cleaning job from an expensive one. The first protects the building: high pressure on asphalt shingles strips the protective granules and can void the roof warranty, and on vinyl it forces water behind panels that have no way to drain. The second protects you, because the discharge obligation does not sit entirely with the contractor once the water is on your property and heading for your drain.

Washing is still the cheapest visible improvement available on commercial property, and on walkways it is a safety item as well — algae and organic film are genuinely slippery when wet, and shaded elevations are where they establish first.

It is just worth buying from someone who will tell you which method each surface gets and where the water is going.

Comparison

Force versus chemistry

One is a hammer and the other is a solvent. The failure mode of using the first where the second belongs is damage you pay to repair on top of the cleaning you already paid for.

Pressure washing
  • Roughly 1,500 to 4,000+ PSI
  • Cleans by mechanical force
  • Right for concrete, hardscape, and durable masonry
  • Rotary surface cleaner on flatwork to avoid striping
  • Removes surface material — including material you wanted
  • Knocks organic growth off without killing it
Soft washing
  • Under 500 PSI, commonly 100 to 300
  • Cleans by chemistry with dwell time
  • Right for shingles, vinyl, stucco, EIFS, wood, paint
  • Applied at volume, allowed to dwell, rinsed gently
  • Surfactants hold solution on vertical surfaces
  • Kills biological growth so it stays gone longer
Why growth comes back. Algae, mildew, and moss are organisms, not dirt. Pressure removes the visible layer and leaves the organism in place, which is why growth cleaned with pressure alone returns quickly. Soft wash solutions use sodium hypochlorite as the biocide with surfactants to extend dwell time and reduce surface tension, so the growth is killed rather than relocated.
Commercial pressure washing across twelve Midwest states
Call 309-796-2222 or request a written bid. Recurring service-area cleaning and one-time building washes.
Call 309-796-2222

Reference

Which method each surface needs

Worth checking against whatever your building is clad in before anyone arrives with a wand. The column on the right is the part that protects the building.

Concrete and masonry flatwork Durable enough for high pressure, cleaned with a rotary surface cleaner rather than a wand to avoid striping. Walks, entries, plazas, drives, and dock aprons. Pressure
Asphalt shingle roofs Soft wash only. High pressure strips the protective granules, shortening roof life and potentially voiding the manufacturer's warranty. Soft wash — never pressure
Vinyl and aluminum siding Soft wash. Pressure can crack, etch, or dislodge panels and force water behind them, where it has no drainage path and mold can establish. Soft wash
Stucco and EIFS Soft wash. High pressure strips the finish, and EIFS in particular is a system that does not tolerate water being driven into it. Soft wash
Painted surfaces Soft wash. Pressure strips coatings — and on older buildings, removing paint can generate chips containing lead that must be captured rather than left on the ground. Soft wash
Wood Soft wash or low pressure. High pressure raises and splinters the grain, which looks worse after cleaning than before. Soft wash
Brick and stone veneer Moderate pressure with appropriate chemistry. Aggressive pressure erodes mortar joints, and the wrong product can etch or discolor stone. Careful pressure
Glass, screens, and seals Low pressure. Pressure tears screen mesh and can break window seals, driving water into the assembly behind. Low pressure

The asphalt shingle entry is the one that costs the most to get wrong. High pressure strips the granules that protect the shingle from UV, which shortens the roof's service life and can void the manufacturer's warranty — and commercial roofs are pressure washed regularly by people who do not know that. If a bidder proposes pressure washing a shingle roof, that single answer tells you what you need to know.

Wash water

The water is industrial wastewater, and it cannot go down your storm drain

Ohio EPA's guidance on mobile power washing states it plainly: power washing wastewater cannot be discharged into a storm sewer. And on a commercial site, the drains in your parking lot almost certainly are storm sewers — which typically discharge untreated to streams and other water bodies. This is the part of exterior cleaning that nobody raises with the property owner.

Call 309-796-2222
“Biodegradable” does not exempt it

The wastewater counts as industrial wastewater even when biodegradable soaps or detergents are used. A green product changes the chemistry, not how the water has to be handled.

A stormwater permit does not cover it

Holding a stormwater NPDES permit does not authorize discharging power washing wastewater to a storm sewer. They are different authorizations, and the distinction is commonly missed.

Evaporation is not a method

Letting wastewater evaporate in a parking lot, a driveway, or a catch basin is not acceptable disposal. It is simply discharge with a delay.

Containment first

No single method is mandated — what matters is that water reaches no storm drain and leaves no site. Berms and containment pads, weighted impermeable drain covers, and a pump or vacuum recovering water as it collects.

Then a permitted route

Sanitary sewer with permission from the local treatment authority, after confirming the line is sanitary and not storm — or collected and hauled to a treatment works or industrial waste facility, which may require samples or pretreatment.

Know where the drain goes

The basic discipline is not discharging to any drain without knowing where it leads. We identify the drain types on site before the first gallon is used.

Requirements differ by state and by treatment authority. Ohio EPA's document is guidance rather than law, and the specifics vary across the states we work in — so we confirm what applies at your property and state the containment and disposal method in the scope. We are contractors, not environmental counsel, and compliance determinations are yours to make with your advisors.

Capabilities

Exterior cleaning we perform

Recurring service-area cleaning and longer-cycle building washes, scoped separately because they run on different intervals.

Call 309-796-2222
Walks & Hardscape
  • Sidewalk and entry cleaning
  • Plaza and courtyard washing
  • Stair and landing cleaning
  • Curb and gutter line cleaning
  • Rotary surface cleaning on flatwork
  • Algae and organic film removal
  • Gum removal
  • Tire mark and traffic film removal
Building Exteriors
  • Soft washing of siding and cladding
  • Stucco and EIFS cleaning
  • Brick and stone veneer cleaning
  • Roof soft washing
  • Awning and canopy cleaning
  • Soffit, fascia, and gutter exteriors
  • Entrance and storefront cleaning
  • Wash prep ahead of painting
Service Areas
  • Dumpster pad and corral cleaning
  • Drive-through lane degreasing
  • Loading dock and apron washing
  • Parking structure and deck washing
  • Trash chute and compactor areas
  • Grease trap surround cleaning
  • Equipment pad cleaning
  • Recurring scheduled service
Stains & Specialty
  • Oil and grease stain treatment
  • Poultice treatment for set stains
  • Rust stain removal
  • Efflorescence treatment on masonry
  • Graffiti removal
  • Hard water and sprinkler staining
  • Hot water and degreaser application
  • Wash water containment and disposal

Reference

What each stain is, and what actually removes it

Most of these do not respond to pressure. Knowing which is which is also how you tell whether a bid is realistic about results.

Oil and grease

Penetrates into the pore structure, so pressure removes only what sits on the surface and leaves a shadow. Hot water with a degreaser and adequate dwell lifts far more; deeply set stains need a poultice drawing oil back out over hours. Ten-year-old drip stands rarely come out completely.

Algae, mildew, and moss

Living organisms rather than dirt. They need a biocide with dwell time, not force — pressure alone removes the visible layer and leaves the growth to return. Shaded and north-facing surfaces are where it establishes first.

Efflorescence

White mineral salts carried to the surface by moisture moving through masonry. A symptom, not a stain — the salts come from inside the assembly, so cleaning without finding the water source means it returns.

Rust staining

Usually from fasteners, railings, rebar, or irrigation water. Needs specific chemistry rather than pressure, and the source has to be addressed or the stain reappears on the same schedule.

Hard water and sprinkler staining

Mineral deposits from irrigation spraying onto walls, glass, and walks. Treatable, and genuinely pointless to treat until the head is redirected. Worth fixing on the irrigation side first.

Gum

Concentrated in entries, at transit stops, and outside doors. Removed with heat and targeted pressure rather than a general wash, and it is usually a separate line item because it is slow work.

Graffiti

Method depends on the substrate and the medium, and the risk is damaging the surface more visibly than the graffiti did. Porous masonry is the hardest case, and speed matters — fresh marks come off far more readily.

Wand striping on concrete

Not a stain but a cleaning defect — alternating light and dark bands left by uneven wand passes, visible once the surface dries. The only remedy is cleaning the whole surface to the same depth, which is why flatwork is done with a rotary surface cleaner.

Paint chips on older buildings

Washing a painted surface hard enough to remove coating generates chips that may contain lead and may be regulated as hazardous waste. They cannot be left on the ground, which makes this a scoped job rather than part of a general wash.

Our work

Entries, walks, and exteriors

Storefront and site work on commercial property we maintain.

Call 309-796-2222
Commercial glass storefront entrance
Glass storefront entrance
New commercial concrete sidewalk and curb
Sidewalk and curb work

Process

How we scope and run a wash

One-time cleanings, pre-paint prep, and recurring service-area schedules all start the same way.

Call 309-796-2222
01

Identify the surfaces and the drains

What each surface is clad in and therefore which method it gets, what the staining actually is, and where every drain in the work area leads. The drain survey happens before the water does.

02

Be honest about results

Set oil, aged graffiti on porous masonry, and existing wand striping all have limits. We say what will come out, what will improve, and what will not, before you approve it.

03

Contain, clean, recover

Berms and covered drains set first, then the appropriate method and chemistry by surface, with the water recovered as it collects and disposed of through the stated route.

04

Phase around your hours

Sections worked one at a time with wet floor signage, outside peak hours for retail and medical property, with the affected areas and timing confirmed before the crew arrives.

About our washing work

What we bring to exterior cleaning

Call 309-796-2222
Method matched to the surface

Soft washing where the cladding requires it and pressure only where it is appropriate. The cheapest wash on the property is the one that does not damage anything.

The water is accounted for

Containment and a permitted disposal route stated in the scope, with drains identified on site first. Not rinsed toward the nearest grate and forgotten.

Honest about what lifts

Set oil, aged graffiti, and existing striping have limits. You will hear them before the work rather than as an explanation afterward.

We know what is behind the surface

We also do the roofing, masonry, painting, and concrete on these buildings, so cleaning is scoped with the assembly in mind rather than only the finish.

Symptoms get reported

Efflorescence, rust staining, and recurring hard water marks all point at something — water in a wall, a corroding fastener, a misdirected head. We tell you rather than just cleaning it again next year.

Single sites to portfolios

One account, one contact, and a consistent standard across every property, in twelve Midwest states. Operating this way since 1996.

Common questions

Pressure washing questions

Environmental notes below are general information, not legal advice. Requirements differ by state and treatment authority.

Call 309-796-2222
What is the difference between pressure washing and soft washing?

Pressure washing works by mechanical force. Soft washing works by chemistry. Using the wrong one is how buildings get damaged by a cleaning service.

Pressure washing runs roughly 1,500 to 4,000 PSI or more and is right for durable surfaces — concrete, masonry, and hardscape that can take the force.

Soft washing runs under 500 PSI, commonly 100 to 300, and some dedicated systems lower still. It applies a cleaning solution at high volume, lets it dwell, and rinses gently. The cleaning is done by the solution rather than the pressure.

The surfaces that need soft washing are the ones most commercial buildings are clad in: asphalt shingles, tile and metal roofs, vinyl and aluminum siding, stucco and EIFS, wood, painted surfaces, and screen enclosures. A contractor who only owns a pressure washer will use a pressure washer on all of them.

What can high pressure actually damage?

More than most property managers expect, and the damage is often not visible the day it happens.

On asphalt shingles, high pressure strips the protective granules from the surface, which shortens the roof's life and can void the manufacturer's warranty. That is the most expensive mistake on this list, and roofs are regularly pressure washed by people who do not know it. See commercial roof repair.

On vinyl siding, pressure can crack, etch, or dislodge panels and force water behind them — where it has no path out and mold can establish. On stucco, EIFS, and painted surfaces it strips the finish. On wood it raises and splinters the grain. It tears screen mesh, and it can break window seals and drive water into wall cavities.

On concrete the damage is subtler but still real: an inconsistent wand pass leaves striping — sometimes called zebra marks — etched into the surface, and once it is there the only remedy is cleaning the whole surface to the same depth. That is why flatwork is done with a rotary surface cleaner rather than a wand.

Can wash water go down the storm drain?

No, and this is the part of the service almost nobody raises with the property owner.

Ohio EPA's guidance on mobile power washing states it directly: you cannot discharge power washing wastewater into a storm sewer. It also makes the point that matters on a commercial site — drains in parking lots usually lead to storm sewers, and storm sewers typically discharge untreated to streams and other water bodies.

Two details catch people out. First, the wastewater is considered industrial wastewater even when biodegradable soaps or detergents are used, so “we use a green product” does not change how it has to be handled. Second, having a stormwater NPDES permit does not authorize discharging power washing wastewater to a storm sewer — those are different things.

Letting it evaporate in a parking lot, a driveway, or a catch basin is also not acceptable.

Requirements differ by state and by the local treatment authority, and Ohio EPA's document is guidance rather than law, so we confirm what applies at your property before the work. But the general principle holds across the states we work in.

So where does the water go?

It gets contained, collected, and disposed of through a route that is actually permitted.

Containment comes first. No single method is mandated — what matters is that water does not reach a storm drain or run off site. In practice that means berms and containment pads, weighted impermeable covers over nearby drains, portable wash pits for equipment, and a pump or vacuum recovering the water as it collects.

Then disposal. The common route is the sanitary sewer with permission from the local treatment authority, after confirming the sewer is sanitary and not storm — and without removing manhole covers. Alternatively the water is collected and hauled to a treatment works or an industrial waste facility, which may require sample results or pretreatment such as filtration or oil and metal removal. Direct discharge to surface water needs an NPDES permit, which takes months and generally does not fit this kind of work.

There is also a route people try that is not acceptable: taking the wastewater to another business, such as a car wash, without permission from that business and from the treatment authority.

Does any of this become hazardous waste?

It can, and the paint case is the one that matters on older commercial buildings.

Where solvents or strong acids are used, the wastewater may qualify as hazardous waste, which carries separate handling requirements entirely.

More commonly: removing paint can produce chips containing metals such as lead, which may be regulated as hazardous waste. Those chips cannot be left on the ground. On a pre-1978 building, washing a painted surface aggressively enough to remove coating is a different job from cleaning it, and it needs to be scoped as one.

This is a reason to tell us what the building is and roughly when it was built before we price washing a painted exterior.

How do you clean concrete without leaving stripes?

With a rotary surface cleaner rather than a hand wand, and by working to a consistent overlap.

Striping happens because a wand delivers an uneven pattern — the center of the fan cleans more aggressively than the edges, so inconsistent passes leave alternating light and dark bands etched into the surface. On a large walk or drive it is immediately obvious once the surface dries.

A surface cleaner holds the nozzles at a fixed height and rotates them, so the cleaning is even across the full width of the head. It is also considerably faster on flatwork, which is why it is standard for commercial work.

The other half is not over-cleaning. Taking one section noticeably deeper than the rest creates a patch that reads as a stain in reverse, and matching it means cleaning everything to that depth.

What removes oil stains from concrete?

Degreasers and dwell time rather than pressure, and the honest answer is that older stains do not always come out completely.

Oil penetrates into the pore structure of concrete. Pressure removes what is on the surface, which is why a pressure-only approach leaves a shadow. A hot water and degreaser approach with adequate dwell lifts considerably more, and for deeply set stains a poultice draws oil back out of the slab over hours rather than minutes.

Fresh spills respond well. A drip stand that has been building for ten years in a drive-through lane is a different proposition, and we will tell you what to expect before the work rather than after. Where a stain genuinely will not lift, coating or replacement is the remaining option. See concrete repair.

What about algae, mildew, and moss?

Those are biological growth, and they need chemistry. Pressure knocks the visible layer off and leaves the organism, which is why growth cleaned with pressure alone returns quickly.

Soft wash solutions use sodium hypochlorite as the biocide — the active ingredient in household bleach — with surfactants added. The surfactants do real work: they help the solution cling to vertical surfaces, extend dwell time, and reduce surface tension so the solution penetrates rather than beads up.

Applied, allowed to dwell, then rinsed gently, that kills the growth rather than relocating it, and the surface stays clean substantially longer.

On walkways this is a safety item as much as an appearance one. Algae and organic film are genuinely slippery when wet, and shaded north-facing walks are where it establishes first.

What is the white powdery residue on our brick?

Most likely efflorescence — mineral salts carried to the surface by moisture moving through the masonry, left behind as the water evaporates.

It matters because it is a symptom rather than a stain. The salts are coming from inside the assembly, which means water is getting into it. Cleaning the surface without addressing the moisture source means it returns, and repeated aggressive cleaning of masonry carries its own risk of damaging mortar joints.

It also responds to different treatment than dirt does, and using the wrong product on masonry can etch or discolor it.

So the useful answer involves looking at why water is in the wall — flashing, sealant joints, coping, grade, or a downspout discharging against it — rather than only at the residue.

How often should a commercial property be washed?

It varies by surface and by what is accumulating, and the right answer is usually different intervals for different areas rather than one property-wide schedule.

Dumpster pads and corrals, drive-through lanes, and service areas accumulate grease and organic material continuously and warrant the most frequent attention — these are also the areas that generate odor and attract pests. Entries and high-traffic walks collect traffic film and show it plainly, since they are the surfaces visitors actually look at. Building exteriors are generally a longer cycle, driven by growth on shaded elevations more than by dirt.

The practical approach on most commercial property is service-area cleaning on a recurring schedule with the building exterior on a longer interval, rather than washing everything at once annually.

Does washing have to happen before painting?

Yes. Coatings need a clean, sound substrate to bond to, and washing is prep rather than an optional improvement beforehand.

Dirt, chalking, organic growth, and loose material all prevent adhesion. Paint applied over them fails early and in ways that look like a coating failure rather than a prep failure.

There is also a timing consideration: the surface has to dry adequately before coating, and masonry and stucco hold moisture longer than people assume. That sequencing is one reason to have the same company do both. See commercial painting.

Can you work without closing the property?

Yes, in sections and usually outside peak hours.

Washing produces water, noise, and temporarily wet surfaces, so areas are worked one at a time with wet floor signage and the section closed until it is safe. For retail and medical property we commonly work early mornings, evenings, or weekends.

Containment adds a constraint worth knowing about: the area around the work has to be bermed and the nearby drains covered, which takes a little more space than the cleaning itself. We confirm the phasing and which areas are affected before starting rather than discovering it on the day.

Request a bid on commercial pressure washing

Tell us the property, what surfaces need cleaning, and roughly when the building was built if it is painted. We’ll follow up to schedule a walk.

309-796-2222
Call or send the form — we answer both.
  • We walk the site and assess the actual condition.
  • You get a priced scope before any work starts.
  • Emergency? Call the number above instead of filling this out.
Request a Bid

Send the details and we’ll be in touch to schedule a site visit.


Call Now