Tell us about the property and the problem. We’ll follow up to schedule a site visit.
Commercial Property Services
Concrete Repair
Sidewalks, curbs, entries, dock aprons, and equipment pads — repaired, replaced, lifted, or resurfaced.
Commercial flatwork and site concrete across twelve Midwest states. Scoped and priced by panel, placed to a specification we will show you.
How concrete fails
Two unrelated failure mechanisms
Commercial concrete fails in two entirely separate ways, and nearly every wrong repair comes from treating one as the other.
Surface deterioration — scaling, spalling, delamination — originates in the concrete itself: air entrainment, finishing, strength, curing, and the deicers applied to it. Structural and subgrade movement — settlement, offset panels, working cracks — originates underneath the slab, in support rather than material.
The distinction decides everything. A settled panel with a sound surface is a candidate for lifting, which is fast and inexpensive. A scaled panel sitting on good subgrade is a candidate for an overlay. Treat the first as a material problem and you resurface a slab that is going to keep sinking. Treat the second as a support problem and you lift a slab whose surface is already gone.
Both mechanisms are worse in this climate than almost anywhere else. Freeze-thaw cycling is the primary driver of surface deterioration, and deicing chemicals intensify it by keeping surfaces saturated and increasing the number of cycles. Frost action in the subgrade drives the movement side — heave when it freezes, loss of support when it thaws.
The useful consequence is that a great deal of concrete condition on a commercial property was determined on the day it was placed. Air content, finishing practice, and whether water was added on site set how a slab will handle twenty Midwest winters. That is why we publish the specification we place to, further down this page.
Reference
What each type of concrete distress indicates
The first question on any concrete condition is which of the two mechanisms produced it. These are the patterns we record most often and what each one points to.
Shallow flaking or peeling of surface mortar across an area. Freeze-thaw damage to a surface with insufficient entrained air, low strength, or a weak finish — intensified by deicers. A surface repair or overlay, not a replacement, where the slab below is sound.
Deeper fragments breaking away, often in patches with rust staining or exposed steel. Chlorides have reached the reinforcement, which corrodes and expands, pushing the concrete off from beneath. Must be taken back to sound concrete with the steel addressed.
The surface sounds hollow when struck but has not broken away yet. A plane of separation below an intact-looking surface, usually a finishing defect. It will become spalling — finding it early with a sounding survey lets it be repaired as a partial-depth patch.
A panel sitting lower than its neighbor. A support problem rather than a concrete problem. Candidate for slab lifting if the panel is sound — but the void has a cause, and a failed storm line or eroding utility trench needs finding before the lift.
Cracks that are widening, offsetting vertically, or moving under load. Structural or subgrade in origin, unlike shrinkage cracking. Sealing them treats the symptom; the movement has to be addressed.
Early, narrow, stable cracks, or a fine cosmetic network of hairlines. Normal behavior rather than a defect. Worth sealing to keep water and chlorides out of the slab, but not a structural concern.
Cracks ignoring the joint pattern. Usually too few control joints, or joints cut too late or too shallow to control where shrinkage went. The slab cracked where it chose because nothing told it where to.
Spalled or broken joint edges with failed or missing sealant. Joints are where most flatwork deterioration begins, because they are the easiest route for water and chlorides into the slab and down to the subgrade.
Water standing on a walk, entry, or apron rather than draining. It keeps the surface saturated, which is the precondition for freeze-thaw damage, and concentrates salt solutions in one place. A grade problem that shortens the life of everything around it.
Reference
Repair methods and when each applies
Concrete is more repairable than most property managers assume. Full replacement is one option among many, and frequently not the right one.
Flatwork is already divided into panels by its joints, which makes selective replacement straightforward — a failed panel comes out at the joints and a new one goes in without disturbing its neighbors. There is no structural reason to replace sound panels, and we price by panel so you can stage the work.
Decision framework
Lift the slab or replace the panel
The practical question on nearly every settled sidewalk and entry. Lifting is faster and cheaper when it applies, and a wasted expense when it does not.
- The panel is structurally intact and not broken into pieces
- The surface is in sound condition
- The problem is loss of support, not the concrete
- The cause of the void is identified and resolvable
- The area needs to return to service quickly
- Matching adjacent panels matters visually
- The panel is badly cracked or in multiple pieces
- The surface has scaled, spalled, or delaminated anyway
- Reinforcement is corroding within the slab
- The void is from a failed utility or storm line needing access
- Subgrade has to be rebuilt or stabilized
- Most panels along the run are failing together
Deicers
The deicer in your salt shed is a concrete decision
Chloride deicers mostly damage concrete indirectly — by keeping surfaces saturated and multiplying freeze-thaw cycles. But chemistry matters, and the National Ready Mixed Concrete Association names specific products that should never touch concrete. Some of them are sold as the gentler option.
NRMCA identifies calcium chloride and sodium chloride — rock salt — as acceptable on sound concrete, used in moderate amounts.
Ammonium sulfate, ammonium nitrate, and magnesium-based salts are described as chemically aggressive to concrete and should never be used. Worth checking what you actually buy.
New concrete should get no deicing chemicals through its first winter. It is still saturated and below full strength — the worst possible moment for them.
Clean sand is the recommended alternative on new work. Inexpensive, effective, and far cheaper than resurfacing a slab that scaled in its first season.
Where salt does get used, hosing off accumulation when conditions allow reduces how long surfaces stay saturated with salt solution.
Poor drainage that lets salt solutions pool raises scaling risk directly. The areas that scale first are usually the low spots and the ground under downspouts.
What we place to
The specification for exterior concrete in this climate
We publish this because it gives you something to ask every bidder. A lower number on a bid sometimes reflects a lower specification rather than better pricing, and air content is where that shows up first.
Figures above follow NRMCA CIP 2, Scaling Concrete Surfaces. For site paving, ACI PRC-330-21 is the industry guide — note that it is a guide rather than a specification, with ACI 330.1 serving that role, so a bid citing 330 as a specification is citing the wrong document.
Our work
Walks, curbs, and steps
Commercial flatwork, curb, and stair work on property we maintain.
Call 309-796-2222
Process
How we scope and price concrete work
Single panels, trip hazard programs, and full replacement all start the same way.
Call 309-796-2222Walk the site and sound the slabs
Distress identified by type and located by panel, with surface deterioration separated from movement. Suspect areas sounded for delamination, and offsets measured against the ADA thresholds rather than estimated.
Find the cause before the method
Voids, settlement, and ponding have causes. We look for the failed line, the eroding trench, or the grade problem first, because a repair over an unresolved cause has a known expiry date.
Itemized bid, priced by panel
Lift, patch, grind, or replace priced per location so work can be phased across budget cycles. Where the cheaper method is adequate, we say so; where it will fail, we explain why.
Placed to spec, then documented
Air content, strength, slump, finishing, and curing to the specification above. Handover includes post-work dimensions and written deicer and sealing guidance for the new work.
About our concrete work
What we bring to concrete work
Air content, strength, slump, finishing, and curing stated openly. Most of a slab's thirty-year performance is decided on placement day, so that is where the scrutiny belongs.
Lifting, grinding, partial-depth patching, and overlays are all on the table. Replacement is one option among several and often not the economical one.
Settlement and voids have reasons. Finding the failed line or the grade problem is what separates a repair that holds from one that recurs on a cycle.
Trip hazards and accessible routes measured to the ADA thresholds, before and after. New flatwork is a chance to fix findings, or to create them.
Deicer and sealing instructions handed over with the work, and relayed to whoever salts the property. The cheapest way to protect what you just paid for.
One account, one contact, and a consistent standard across every property, in twelve Midwest states. Operating this way since 1996.
Common questions
Concrete repair questions
If your question is not covered, call and ask. We would rather answer it directly than have you work from an assumption.
Call 309-796-2222What is the difference between scaling and spalling?
They look similar and they are not the same problem, which matters because the repairs differ.
Scaling is the flaking or peeling of the surface mortar, generally shallow and spread across an area. The National Ready Mixed Concrete Association describes it as the result of repeated freezing and thawing: as saturated concrete approaches freezing, water expands into ice and stresses the surface. Deicing chemicals make it worse by keeping the surface saturated and increasing the number of freeze-thaw cycles.
Spalling is deeper — fragments breaking away from the body of the slab, often in distinct patches and frequently over reinforcing steel. Where rebar is involved, the mechanism is usually chloride-driven corrosion: salt reaches the steel, the steel corrodes, corrosion products occupy more volume than the original metal, and the expansion pushes the concrete off from beneath.
Scaling is typically a surface repair or an overlay. Spalling over corroding steel has to be taken back to sound concrete with the steel treated or replaced, because patching over active corrosion just relocates the failure.
Why did our concrete start scaling when the sidewalk next to it is fine?
Almost always air entrainment, finishing, or added water — meaning the difference was established the day it was placed, not by what has happened since.
Entrained air is the defense against freeze-thaw. It creates millions of microscopic bubbles that give expanding ice somewhere to go. NRMCA's recommended total air content is 6 percent for concrete with 3/4-inch or 1-inch coarse aggregate. Concrete placed without it, or with too little at the surface, has no mechanism to absorb that expansion.
Finishing destroys it just as effectively. Overworking the surface drives entrained air out of the top layer, finishing while bleed water is still present produces a weak surface mortar, and steel troweling an exterior slab seals and weakens the very surface that has to survive winter. NRMCA notes a broom finish is adequate for most exterior work.
Then there is water added on site to make placement easier. It raises the water content, promotes bleeding and segregation, and weakens the surface. Two slabs placed the same week by different crews can have genuinely different life expectancies for this reason alone.
Does deicing salt damage concrete?
The relationship is more specific than yes or no, and the chemistry you buy matters more than the quantity.
Chloride deicers do not attack sound, properly air-entrained concrete directly so much as they worsen the freeze-thaw cycle — they keep the surface saturated and increase the number of cycles it goes through. On concrete that is already low in entrained air, low in strength, or poorly finished, that is enough to cause scaling.
Chemistry is the part most property managers have never been told. NRMCA identifies calcium chloride and sodium chloride (rock salt) as acceptable, and states that ammonium sulfate, ammonium nitrate, and magnesium-based salts are chemically aggressive to concrete and should never be used. That is worth checking against whatever is actually in your salt shed, because some of those are marketed as gentler alternatives.
The other factor is drainage. Poor drainage that lets salt solutions pool raises scaling risk, which is why the places that scale first are usually the low spots and the areas under downspouts.
Can deicers be used on concrete we just had poured?
Not during the first winter, and this is the single most valuable thing we can tell a client about protecting new work.
NRMCA's guidance is to avoid deicing chemicals on new concrete through its first winter, then use them in moderate amounts afterward. New concrete is still relatively saturated and has not reached its full strength, and that is exactly the condition in which deicers do the most damage.
Use clean sand for traction instead. It is inexpensive, it works, and it costs nothing compared with resurfacing a slab that scaled in its first season. Where salt does get used, hosing off accumulation when conditions allow helps.
We put this in writing when we hand over new flatwork, and we will brief whoever handles your snow and ice so the instruction actually reaches the person with the spreader. See snow and ice removal.
Should new concrete be sealed?
Yes, for exterior flatwork in this climate — with the right product and at the right time.
NRMCA recommends a breathable silane or siloxane sealer intended for slabs, applied once the concrete is reasonably dry and following the manufacturer's directions. Late summer, after a few dry days, is described as ideal.
The word doing the work there is breathable. A film-forming sealer that traps moisture in the slab can make freeze-thaw damage worse rather than better, which is the opposite of the intent. Penetrating silane and siloxane products reduce water absorption while still letting the slab dry.
Resealing on a cycle is reasonable maintenance and considerably cheaper than surface repair.
A sidewalk panel has settled. Can it be lifted instead of replaced?
Often, and it is usually both faster and less expensive when the slab itself is sound.
Slab lifting — polyurethane foam injection, or cement-based slurry in the traditional mudjacking approach — raises a settled slab back to grade by filling the void beneath it. It is appropriate when the panel is structurally intact and the problem is support rather than the concrete, and the area can generally return to service the same day with foam.
Replacement is the answer when the panel is badly cracked or broken into multiple pieces, when the surface has deteriorated anyway, or when the void is a symptom of something that has to be opened up and corrected — a failed storm line, an eroding utility trench, or subgrade that needs to be rebuilt.
Lifting a slab over an unresolved cause buys you a level walk and the same settlement again. We look for the reason before quoting the lift.
Is grinding a trip hazard an acceptable repair?
Sometimes, and it has clear limits.
Grinding or saw-cutting a vertical offset to a compliant transition is a legitimate and inexpensive fix for modest displacement where both panels are otherwise sound. It is quick, there is no cure time, and the walk is usable immediately.
It stops being appropriate when the offset is large enough that grinding would remove too much section or expose aggregate and reinforcement, when the panels have deteriorated, or when the cause is ongoing settlement that will reproduce the offset.
Under the ADA standards, a vertical change up to 1/4 inch is permitted as-is, between 1/4 and 1/2 inch must be beveled no steeper than 1:2, and anything over 1/2 inch has to be ramped. Those thresholds are what determine whether grinding resolves the condition or merely improves it. See ADA access, ramps and bollards.
What specification should commercial exterior concrete be placed to?
For this climate, the figures that matter most are air content, strength, and slump — and they are worth asking every bidder about, because a lower number on a bid sometimes reflects a lower specification rather than better pricing.
NRMCA's guidance for exterior slabs: total air content of 6 percent for concrete with 3/4-inch or 1-inch coarse aggregate. Compressive strength of 4000 psi for exterior slabs that will be continuously moist and receive deicers, with 3500 psi as the minimum where those conditions do not apply. Slump of 3 to 5 inches, with no water added on site.
Supplementary cementitious materials are limited to 25 percent fly ash, 50 percent slag cement, or 10 percent silica fume by weight of cementitious material.
For site paving specifically, ACI PRC-330-21, Commercial Concrete Parking Lots and Site Paving Design and Construction—Guide, is the industry reference. It is a guide rather than a specification — ACI 330.1 serves that purpose — and it covers thickness design, jointing, subgrade, accessibility surface requirements, and maintenance and repair.
When can concrete be placed in the Midwest?
Most of the year, with real caution at both ends of it.
NRMCA advises care when placing exterior concrete in late fall, winter, or early spring, because concrete that freezes soon after placement while still saturated is at high risk. Cold-weather placement is possible with blankets, heat, and mix adjustments, but it adds cost and it narrows the margin for error.
The practical consequence is scheduling. Exterior flatwork planned over the winter gets placed in favorable conditions in spring and early summer, which also puts it in position to be sealed in late summer as recommended, and to reach its first winter at full strength.
Where a repair genuinely cannot wait — a trip hazard, a failed entry, a broken dock apron — we will do it in the conditions available and tell you plainly what that means for its expected life.
Why does concrete crack, and which cracks matter?
Concrete shrinks as it cures and moves with temperature, so some cracking is expected rather than a defect. The useful question is which kind you have.
Fine surface crazing is a cosmetic network of hairlines and generally not a structural concern. Shrinkage cracking appears early and is usually narrow and stable. Control joints exist to put shrinkage cracking where you chose rather than where the slab decides, which is why slabs with too few joints, or joints cut too late or too shallow, crack randomly.
The cracks that matter are the ones that are widening, offsetting vertically, or working — moving under load. Those indicate subgrade or structural issues rather than shrinkage, and sealing them treats the symptom.
Sealing stable cracks is still worth doing. It keeps water and chlorides out of the slab and away from any reinforcement, which is the same logic that makes crack sealing the highest-value operation on asphalt.
Can you repair just the bad panels rather than the whole walk?
Yes, and panel-by-panel replacement is how most commercial flatwork should be handled.
Concrete flatwork is already divided into panels by its joints, which makes selective replacement straightforward — a failed panel comes out at the joints and a new one goes in without disturbing its neighbors. There is no structural reason to replace sound panels.
We scope and price by panel, which lets you address the trip hazards and failed sections now and stage the rest across budget cycles. It also gives you a documented record of which panels were replaced and when, which is useful if a claim ever arrives.
The honest exception: where most panels along a run are failing, replacing the run is usually cheaper per square foot than replacing them individually over several years, and we will say so.
Do you handle the curb, the pavement, and the ADA work together?
Yes, and on most sites those are the same job.
The curb line decides whether water leaves the lot or sits in it, so curb and gutter repair is frequently what makes an adjacent pavement repair last. Entry slabs, approach aprons, dock aprons, equipment pads, and bollard footings are all concrete work sitting against asphalt.
Accessibility is the other overlap. Walks, ramps, landings, and the route from accessible parking are concrete elements with dimensional requirements — cross slope, running slope, clear width, and level changes — and we measure those rather than assume them. See parking lot repair and ADA access work.
Related services
Commonly scoped alongside concrete work
Pavement, accessibility, and dock work almost always touch the same concrete.
All ServicesRequest a bid on concrete repair
Tell us the property and what you are seeing — trip hazards, scaling, a settled panel, or a broken curb. We’ll follow up to schedule a walk.
309-796-2222- We walk the site and assess the actual condition.
- You get a priced scope before any work starts.
- Emergency? Call the number above instead of filling this out.
Send the details and we’ll be in touch to schedule a site visit.